The dishwasher "AEG" does not start, the malfunction code is lit on the display. What does it mean? So the machine’s self-diagnosis system informs the user about a breakdown. Having decrypted the code, you will understand where to look for the cause of the malfunction.
If the breakdown is not serious, you can fix it yourself or call a specialist.
How AEG codes are decrypted
If you started the dishwasher and first saw a trouble code, try rebooting. Perhaps a network failure occurred, so the system generated an error.
How to restart the AEG dishwasher? Unplug it for a few minutes, then turn it back on. Did the error go away? You can load and wash the dishes. If the code is highlighted again, search for damage.
Malfunction code | Number of blinks for cars with indicator | Value | Reason for occurrence | DIY repair |
I 10 | 1 | No water in the car. Waiting time exceeded. | 1. Problems with the water level sensor. 2. Clogged or pinched inlet hose. 3. The inlet tap is blocked, there is no water in the water supply. 4. The intake valve is broken. | 1. The details are held. In the event of a malfunction, it is replaced. 2. Inspection of the inlet hose, cleaning from blockage. 3. Checking the water in the water supply. 4. Diagnosis of the filler valve. Replace if necessary. |
I 20 | 2 | There is no discharge of water. | 1. The drainage system is clogged. 2. The drain hose has pinched. 3. Problems with the water level sensor. 4. Damage to the PMM drain pump. | How to fix the situation: 1. Check the drain hose for blockage and kink. 2. The level sensor is inspected, a new part is installed in case of a malfunction. 3. The drain pump is inspected and cleaned of debris. If the pump is defective, replace it. |
I 30 | 3 | Protection "Aquastop" has worked. | Water has been detected in the pan of the dishwasher and a leak has occurred. Either the float sensor is faulty. | 1. The PMM case and connections are inspected at the time of the leak. 2. Diagnostics of the Aquastop system. |
I 50 | 5 | Problems with the control module. | The triac of the module that controls the pump is faulty. | Need diagnostics and repair of the main module. |
I 60 | 6 | What does the code mean: water does not heat up or overheat. | 1. The heating element has burned out. 2. Damage to the level sensor. 3. Faulty pump. 4. There are problems with the thermistor. 4. The control module of the dishwasher is faulty. | What can be done if this code appears: 1. Check and replace the heater. 2. Inspect the level sensor, its connections. Install a new part if broken. 3. If there are problems with the installation of the machine or pump, the water is constantly drained, so heating does not occur. Need to check the connection system, as well as the efficiency of the pump. |
I 70 | 7 | Wiring problems, NTC short circuit. | Check and replace wiring. Inspection of the NTC sensor. | |
I 80 and I 90 | 8-9 | Communication problems with eeprom or module firmware. | Faulty electronic module. | Diagnostics and repair or module replacement. |
I A0 | 10 | Sprayer does not work. | It is necessary to check and unlock the sprinkler. | |
I b 0 | 11 | There are problems with the turbidity sensor. | 1. Turbidity sensor does not work. 2. Need to clean the dishwasher. | 1. Check and replace the turbidity sensor. 2. Cleaning the PMM. |
I C0 | 12 | There is no communication with the user interface. | Malfunction of the main module. System crash. | The dishwasher needs a reboot. If the error persists, the module is diagnosed and repaired. |
I ad0 | 13 | No tacho signal. | 1. There is no heating of water. 2. Uncontrolled engine speed. | The tachogenerator needs checking and replacement. |
I F0 | 14 | No water intake. | Weak pressure in the water supply. | You need to wait until the normal flow of water resumes. |
Now you know the errors of the AEG dishwashers and can read their codes. Eliminate blockage in the machine under the power of each user. As for the replacement and repair of parts, it is better to entrust this work to the master.